Plumbing Basics: A Prerequisite for When Installing a Bathtub
Plumbing Basics: A Prerequisite for When Installing a Bathtub
Blog Article
This article down below in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is immensely interesting. Read it for yourself and figure out what you think of it.
Mounting a bathtub isn't exactly brain surgery, however it does call for strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging project. If the old bathtub is easily accessible, the job can move immediately; if you have to open a wall surface to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will need an assistant to vacate the old tub and also set in the new one. Make certain you have certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to think about employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This post will assist you mount a new bathtub in your washroom if you have actually already purchased a brand-new bathtub and don't need to alter the plan of your previous water system pipelines.
Your tools as well as material checklist need to comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing taps can be quite bothersome as a result of the limited accessibility that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. When the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Secure the tap in position with the maker supplied backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, put the bath tub in the required setting. The wood boards are valuable in uniformly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small points.
The next objective is to make sure that the tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and inspect all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait till the bathtub has actually been utilized a minimum of when as this will settle it into its last setting.
Preparing for the Setup
To start with, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, causing the water to permeate the wall in between the bath as well as the tiling, bring about difficulties with moisture and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to enable the motion experienced when the tub remains in usage. The sealant can crack relatively early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is suggested to fit the tiles using waterproof or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I came across that post about Installing A Bathtub when exploring the search engines. Do you know about anybody else who is very much interested in the subject? Take a moment to share it. I thank you for reading our article about How to Install a Bathtub.
Schedule A Service Call Report this page