Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
Almost everyone has their personal thinking when it comes to How to Install a Bathtub.
Setting up a bath tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard job. If the old tub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old tub as well as position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also embeded in the brand-new one. Make certain you have qualified yourself for the job and fit trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may need an expert plumber to make tube links.
This article will help you set up a new tub in your washroom if you have actually currently bought a new bathtub and also don't need to alter the arrangement of your previous supply of water pipelines.
Your devices and also material list must make up the following:
Planning for the Setup
First of all, the sustaining frame provided with the bath should be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing faucets can be fairly problematic due to the restricted access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. When the supply pipelines have been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, put the bath tub in the required setting. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the tub up until the level reviews level.
To mount faucets, fit all-time low of the furthest flexible tap port to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Switch on the supply of water and check all joints and also new pipework for leakages and also tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used at the very least once as this will certainly resolve it into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washers are in area between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The former type should be linked to the tap finishes first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, causing problems with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, as well as can securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can break rather early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our piece about Installing A Bathtub. Thanks for taking a few minutes to read through our posting. Kindly take the time to promote this content if you liked it. Kudos for your time. Kindly stop by our blog back soon.
Tailored care available. Report this page